It ’ randomness pretty simple but there are lots of steps .
First off, you need to figure out how many shelves you want and what size they need to be.
Reading: How to install shelves in a closet
I settled on 4 new shelves, plus the original one already in the closet. I chose to leave the original shelf and the clothes rod hardware in the wardrobe, fair in case we always want to convert it back to a clothing closet .
I wanted two extra shelves that were the lapp astuteness as the original shelf, and then two lower shelves that were deeper .
so I needed 4 shelves, all the like width ; two of them 11″ deep, two of them 18″ deep .
I besides needed a crowd of 1x2s to support the shelves, and 4 metal “ L ” brackets to support the plaza of each shelf because the shelves were indeed farseeing I was afraid of bowing .
Sheets of MDF are importantly cheaper than pre-cut sheets of MDF or wood, so I chose to purchase two sheets of MDF and have our local hardware store cut it for me .
*Note : I had our local anesthetic hardware shop cut the MDF into the proper WIDTH but I left them 8′ hanker until I got home and cut them to length myself .
once I got home with my pre-cut MDF and all my 1x2s, I laid them out in the garage so I could prime them. I learned the heavily room while doing K ’ s board and batten that it ’ s easier to prime MDF before you install it .
I primed each control panel with two coats. Make sure you prime the movement edge of your shelves equally well .
When the primer was dry, it was time to begin the install action .
This may sound foreign, but you MUST insert all your boards into your closet BEFORE you start adding all your 1×2 supports, like this :
If you add all your 1x2s beginning, it will be impossible to get the shelves into the water closet because the first step of the closet is smaller than the actual closet .
once your shelves are inside the wardrobe, start adding your 1×2 supports. I added them all equal distance apart, so a little mathematics was involved. 😉
I used my nail gun to attach all the supports, but you might want to consider adding a few screws into the stud for extra accompaniment .
now I know you are itching to put those shelves improving now, but you still have to get your center bracket into place .
first gear, add a board a little broad and longer than your “ L ” bracket. The “ L ” bracket will screw into this board .
I added mine slenderly off-center so they would line up perfectly with the bracket from the original ledge.
now it ’ south time to add the “ L ” brackets. Use some heavy duty screws when you attach the bracket to the support board .
And now, finally, you can pull the shelves up one at a time and plop them into identify .
I added several nails into the top of each shelf, down into the 1×2 supports below. You don ’ metric ton want your ledge to budge, so adding nails to secure it is a adept idea .
If you noticed, there are lots of nail holes and uglyness with my shelves. I filled all the pinpoint holes with spackle and then I used caulk around all the exposed edges of forest, just to give it a more polish look .
once everything was puttied up and dry, I used a small foam roller to add two coats of semi-gloss white paint ( Alabaster from Sherwin Williams ) to the tops and fronts of each board. I besides used a small lean brush to paint all the 1×2 supports .
I actually wasn ’ thyroxine concerned about getting paint and caulk all over the walls because once the blank shelf paint dried, I planned to paint the walls .
And hera it is now that the walls are all painted :
I used some leftover paint in my garage that my friend gave to me. She had it coloring material matched from somewhere so honestly, I have NO CLUE what color it is. It ’ s a colored fuscous color with a grey undertone .
here you can see how the penetrate shelves are deeper than the upper berth ones .
There was thus much extra room in the front of the closet that I didn ’ t want to waste, so I ’ meter glad I made the shelves 18″ deep. They hold a long ton !
And THAT, my friends, is how you install shelves in a closet. not besides hard, precisely a fortune of steps .
If you have any extra tips or pointers that I missed, I ’ d beloved to hear them .
A few thoughts about my shelves now that I ’ molarity finished :
- I used 1/2″ thick MDF. In hindsight I should have used the next size up (7/8″ I think?) so the shelves would be even more sturdy.
- I nailed all the 1x2s into the wall & studs. I may go back and add a few screws into the studs for additional support.
hopefully this helped you realize that you can do stuff like this. Don ’ t drive overwhelmed with the entire project, just take it one step at a time.
Read more: How To Skim Fat Off Of Broth Recipes
Thanks for reading ! Have a fantastic week !